您好,欢迎光临莱州聚峰机械有限公司网站!

服务热线

400-879-1999

你所在位置: 首页 >> 新闻资讯 > 行业资讯
行业资讯

自动上料混凝土搅拌车在使用中应该注意什么?

来源:http://www.zkzdsljbc.com/ 时间:2021-04-23

1.搅拌车发动机启动后,搅拌筒应低速运行约10分钟,以便在液压油之前,液压油的温度升20°C以上。
1. After the mixer engine is started, the mixer drum should run at a low speed for about 10 minutes, so that the temperature of the hydraulic oil rises to 20 ℃ before activating the hydraulic oil ° C or above.
2.在此之前,将搅拌桶上下颠倒。
2. Before that, turn the mixing drum upside down.
6.自动喂料搅拌机运输的混凝土坍落度必须少为8厘米。从混凝土进入储罐到卸货,温度在高温下不应超过2小时,在阴雨天则不应超过2.5小时。
6. The slump of concrete transported by automatic feeding mixer must be at least 8 cm. From the time of concrete entering the storage tank to unloading, the temperature should not exceed 2 hours under high temperature and 2.5 hours in rainy days.
7.在从搅拌机中取出混凝土之前,应将搅拌槽以10-12 rpm的转速旋转1分钟。
7. The mixing tank shall be rotated at 10-12 rpm for 1 minute before concrete is removed from the mixer.
8.混凝土搅拌机卸载汽车后,使用卡车软管清洁进水口,卸载料斗和卸载箱之类的零件,以卡车车身各个部分上的灰尘和残留混凝土。倒入搅拌桶中,注入150-。 200公升纯净水。在返回过程中,缓慢旋转混合槽以清洁内壁,以防止残留的炉渣粘附到混合槽壁和混合叶片上,并在重新加注之前将水排干。
8. After unloading the truck with the concrete mixer, use the truck hose to clean the water inlet, unloading hopper, unloading box and other parts to remove the dust and residual concrete on each part of the truck body. Pour into the mixing drum and add 150 -. 200 liters of purified water. During the return process, slowly rotate the mixing tank to clean the inner wall to prevent the residual slag from adhering to the mixing tank wall and mixing blades, and drain the water before refilling.
9.当混凝土搅拌车运输混凝土时,发动机转速应在1000-1400 rpm的范围内,以确保发动机的扭矩。在运输混凝土的过程中,为了驾驶,车速不应超过40 km / h。
9. When the concrete mixer transports concrete, the engine speed should be in the range of 1000-1400rpm to ensure the maximum torque of the engine. In the process of transporting concrete, in order to drive safely, the speed should not exceed 40 km / h.
10.完成水泥搅拌车的工作后,清洁搅拌车的内部和主体,不要在搅拌车上留下任何残留的混凝土。
10. After finishing the work of the cement mixer, clean the inside and main body of the mixer, and do not leave any residual concrete on the mixer.
1.1。在开始搅拌机轨道之前,搅拌机鼓的操作手柄必须处于“停止”位置。
1.1。 Before starting the mixer track, the operating handle of the mixer drum must be in the "stop" position.
2.2。搅拌车启动发动机后,以低速旋转搅拌桶约10分钟,以使液压油温度超过20°C,然后再开始运行。
2.2。 After the mixer starts the engine, rotate the mixing drum at a low speed for about 10 minutes to make the hydraulic oil temperature exceed 20 ℃ ° C. Then start running again.
3.3。如果搅拌车停在室外,则在装载前应将搅拌桶倒转以排放水和碎屑,以确保混凝土质量。
3.3。 If the mixer truck is parked outside, the mixing drum should be reversed to drain water and debris before loading to ensure the quality of concrete.
4.4。搅拌车运输混凝土时,必须将其牢固放置,以免因松动滑桶,损坏行人或影响其他车辆的正常运转而摆动。
4.4。 When concrete is transported by mixer truck, it must be placed firmly to avoid swinging due to loosening sliding bucket, damaging pedestrians or affecting normal operation of other vehicles.
5.当搅拌车装载混合混凝土时,搅拌桶的速度为2-10 rpm。在运输过程中,在平坦路面上搅拌桶的速度保证为2-3 rpm。在超过50的侧坡上行驶和在左右摇摆较大的道路上行驶时,必须在路面状况得到改善后停止混合料灌浆并重新开始混合料灌浆。
小型混凝土搅拌车
5. When the mixer truck loads the mixed concrete, the speed of the mixing drum is 2-10 rpm. During transportation, the speed of the mixing drum is guaranteed to be 2-3 rpm on the flat road. When driving on the side slope over 50 and on the road with large left-right swing, the mixture grouting must be stopped and restarted after the road condition is improved.
6.混凝土搅拌车运输混凝土的时间不得超过搅拌站规定的时间。在运输混凝土期间,请勿长时间停止搅拌桶,以防止混凝土偏析。
6. The time of transporting concrete by concrete mixer truck shall not exceed the time specified by mixing station. During the transportation of concrete, do not stop the mixing bucket for a long time to prevent concrete segregation.
7.如果搅拌车装满混凝土,现场停滞时间不应超过一小时。如果超时,现场人员将不得不及时处理。
7. If the mixer truck is full of concrete, the site dead time shall not exceed one hour. In case of overtime, the on-site personnel will have to deal with it in time.
8.搅拌车运输的混凝土块必须少8厘米。从混凝土进入储罐开始直排出为止,在炎热天气下排出不应超过2小时,在寒冷天气下排出不应超过2.5小时。
8. Concrete blocks transported by mixer truck must be at least 8 cm. From the beginning of concrete entering the storage tank to discharging, the discharging time shall not exceed 2 hours in hot weather and 2.5 hours in cold weather.
9.在搅拌车弹出混凝土之前,以10-12 rpm的速度旋转搅拌桶1分钟,然后弹出。
9. Before the concrete is ejected by the mixer truck, rotate the mixing drum at the speed of 10-12 rpm for 1 minute, and then eject.
10.混凝土搅拌机排干车后,立即使用卡车附带的软管冲洗进水口,排水料斗和排水槽,以车身上的污垢和残留的混凝土。将150-200L的清水倒入搅拌桶中。
10. After the concrete mixer dries the truck, immediately use the hose attached to the truck to flush the water inlet, drain hopper and drain trough to remove dirt and residual concrete from the truck body. Pour 150-200l clean water into the mixing bucket.
以上的精彩内容来自:小型混凝土搅拌车更多的精彩内容请点击进入我们的网站:http://www.zkzdsljbc.com,我们后续会有更多的精彩内容等您查看,请继续关注我们。
The above wonderful content comes from: small concrete mixer. For more wonderful content, please click to enter our website: http://www.zkzdsljbc.com , we will have more wonderful content waiting for you to check, please continue to pay attention to us.
上一篇:自动上料混凝土搅拌车在使用中应该注意什么?
下一篇:全自动搅拌车购买后怎么开?
tag:混凝土搅拌车,小型混凝土搅拌车,全自动混凝土搅拌车
当前位置: 首页 - 新闻资讯 > 行业资讯

自动上料混凝土搅拌车在使用中应该注意什么?

作者:中科聚峰混凝土搅拌车厂家 时间:2021-04-23

1.搅拌车发动机启动后,搅拌筒应低速运行约10分钟,以便在液压油之前,液压油的温度升20°C以上。
1. After the mixer engine is started, the mixer drum should run at a low speed for about 10 minutes, so that the temperature of the hydraulic oil rises to 20 ℃ before activating the hydraulic oil ° C or above.
2.在此之前,将搅拌桶上下颠倒。
2. Before that, turn the mixing drum upside down.
6.自动喂料搅拌机运输的混凝土坍落度必须少为8厘米。从混凝土进入储罐到卸货,温度在高温下不应超过2小时,在阴雨天则不应超过2.5小时。
6. The slump of concrete transported by automatic feeding mixer must be at least 8 cm. From the time of concrete entering the storage tank to unloading, the temperature should not exceed 2 hours under high temperature and 2.5 hours in rainy days.
7.在从搅拌机中取出混凝土之前,应将搅拌槽以10-12 rpm的转速旋转1分钟。
7. The mixing tank shall be rotated at 10-12 rpm for 1 minute before concrete is removed from the mixer.
8.混凝土搅拌机卸载汽车后,使用卡车软管清洁进水口,卸载料斗和卸载箱之类的零件,以卡车车身各个部分上的灰尘和残留混凝土。倒入搅拌桶中,注入150-。 200公升纯净水。在返回过程中,缓慢旋转混合槽以清洁内壁,以防止残留的炉渣粘附到混合槽壁和混合叶片上,并在重新加注之前将水排干。
8. After unloading the truck with the concrete mixer, use the truck hose to clean the water inlet, unloading hopper, unloading box and other parts to remove the dust and residual concrete on each part of the truck body. Pour into the mixing drum and add 150 -. 200 liters of purified water. During the return process, slowly rotate the mixing tank to clean the inner wall to prevent the residual slag from adhering to the mixing tank wall and mixing blades, and drain the water before refilling.
9.当混凝土搅拌车运输混凝土时,发动机转速应在1000-1400 rpm的范围内,以确保发动机的扭矩。在运输混凝土的过程中,为了驾驶,车速不应超过40 km / h。
9. When the concrete mixer transports concrete, the engine speed should be in the range of 1000-1400rpm to ensure the maximum torque of the engine. In the process of transporting concrete, in order to drive safely, the speed should not exceed 40 km / h.
10.完成水泥搅拌车的工作后,清洁搅拌车的内部和主体,不要在搅拌车上留下任何残留的混凝土。
10. After finishing the work of the cement mixer, clean the inside and main body of the mixer, and do not leave any residual concrete on the mixer.
1.1。在开始搅拌机轨道之前,搅拌机鼓的操作手柄必须处于“停止”位置。
1.1。 Before starting the mixer track, the operating handle of the mixer drum must be in the "stop" position.
2.2。搅拌车启动发动机后,以低速旋转搅拌桶约10分钟,以使液压油温度超过20°C,然后再开始运行。
2.2。 After the mixer starts the engine, rotate the mixing drum at a low speed for about 10 minutes to make the hydraulic oil temperature exceed 20 ℃ ° C. Then start running again.
3.3。如果搅拌车停在室外,则在装载前应将搅拌桶倒转以排放水和碎屑,以确保混凝土质量。
3.3。 If the mixer truck is parked outside, the mixing drum should be reversed to drain water and debris before loading to ensure the quality of concrete.
4.4。搅拌车运输混凝土时,必须将其牢固放置,以免因松动滑桶,损坏行人或影响其他车辆的正常运转而摆动。
4.4。 When concrete is transported by mixer truck, it must be placed firmly to avoid swinging due to loosening sliding bucket, damaging pedestrians or affecting normal operation of other vehicles.
5.当搅拌车装载混合混凝土时,搅拌桶的速度为2-10 rpm。在运输过程中,在平坦路面上搅拌桶的速度保证为2-3 rpm。在超过50的侧坡上行驶和在左右摇摆较大的道路上行驶时,必须在路面状况得到改善后停止混合料灌浆并重新开始混合料灌浆。
小型混凝土搅拌车
5. When the mixer truck loads the mixed concrete, the speed of the mixing drum is 2-10 rpm. During transportation, the speed of the mixing drum is guaranteed to be 2-3 rpm on the flat road. When driving on the side slope over 50 and on the road with large left-right swing, the mixture grouting must be stopped and restarted after the road condition is improved.
6.混凝土搅拌车运输混凝土的时间不得超过搅拌站规定的时间。在运输混凝土期间,请勿长时间停止搅拌桶,以防止混凝土偏析。
6. The time of transporting concrete by concrete mixer truck shall not exceed the time specified by mixing station. During the transportation of concrete, do not stop the mixing bucket for a long time to prevent concrete segregation.
7.如果搅拌车装满混凝土,现场停滞时间不应超过一小时。如果超时,现场人员将不得不及时处理。
7. If the mixer truck is full of concrete, the site dead time shall not exceed one hour. In case of overtime, the on-site personnel will have to deal with it in time.
8.搅拌车运输的混凝土块必须少8厘米。从混凝土进入储罐开始直排出为止,在炎热天气下排出不应超过2小时,在寒冷天气下排出不应超过2.5小时。
8. Concrete blocks transported by mixer truck must be at least 8 cm. From the beginning of concrete entering the storage tank to discharging, the discharging time shall not exceed 2 hours in hot weather and 2.5 hours in cold weather.
9.在搅拌车弹出混凝土之前,以10-12 rpm的速度旋转搅拌桶1分钟,然后弹出。
9. Before the concrete is ejected by the mixer truck, rotate the mixing drum at the speed of 10-12 rpm for 1 minute, and then eject.
10.混凝土搅拌机排干车后,立即使用卡车附带的软管冲洗进水口,排水料斗和排水槽,以车身上的污垢和残留的混凝土。将150-200L的清水倒入搅拌桶中。
10. After the concrete mixer dries the truck, immediately use the hose attached to the truck to flush the water inlet, drain hopper and drain trough to remove dirt and residual concrete from the truck body. Pour 150-200l clean water into the mixing bucket.
以上的精彩内容来自:小型混凝土搅拌车更多的精彩内容请点击进入我们的网站:http://www.zkzdsljbc.com,我们后续会有更多的精彩内容等您查看,请继续关注我们。
The above wonderful content comes from: small concrete mixer. For more wonderful content, please click to enter our website: http://www.zkzdsljbc.com , we will have more wonderful content waiting for you to check, please continue to pay attention to us.

截屏,微信识别二维码